MouseTester.io

Mouse double click test

Press every mouse button here, then click left and right 20 times each
Left0
Middle0
Right0
Back0
Forward0

Result

Not started
Possible faulty double-clicks
— Press a button to start 20 clicks per button
Shortest gap and thresholdDrag to set
Single0
Double0
Fault0
Press any button in the test area to start

Hold time

Gaps between presses

Gaps: 0
Double median—
Single median—
Faults—

Event log

SingleDouble-clickPossible faultNewest first · scale 0–400 ms

How to test

About 1 minute
01
Press every buttonTest all five
02
20 clicks eachClick as usual
03
Look for amberAmber marks a fault
04
Repeat 2 or 3 timesTest again
Single≥300 ms
Double-click80–300 ms
Possible fault<80 ms

Inside a micro switch

Pressing the button pushes the plunger onto the leaf spring, which snaps over and carries the moving contact from the normally closed (NC) contact to the normally open (NO) one. That closes the circuit and sends a click. Metal contacts bounce as they meet, and that is where double-clicks begin.

Mechanical switch

The contacts bounce for a few ms as they close, and the firmware filters it out. Oxidized contacts bounce longer.

Optical switch

A press interrupts a light beam. With no metal contacts, nothing can bounce.

Lifespan

Rated for tens of millions of clicks, but humidity and dust shorten it. The left button usually fails first.

Why a switch double-clicks

Contacts bounce for a few milliseconds as they close, so the firmware ignores that window (debounce). A worn switch keeps bouncing after it and one press reads as two, which a mouse double clicking test catches.

Finger press
Good switch
1 click
Worn switch
2 clicks
Debounce window: the firmware ignores the signalBounce after the window
Mechanical bounceMetal contacts bounce a few times on closing
Oxidized contactsHigher resistance makes the signal flicker
Short debounce timeBounce outlasts it
Optical switchUses light instead of contacts, so no bounce
ImpactIn games, weapons misfire and abilities get cancelled; at work, files open twice and drags drop halfway.

What the readings mean

Cases: 6
Possible fault in the event logCauseOne press read as twoFixTest 2–3 more times; contact the brand if it repeats
Bounces in the hold timesCauseContacts reopenFixReplace the switch, especially if faults show too
Left button onlyCauseIt gets the most useFixUse the warranty, or replace the left switch
A gap right at the thresholdCauseA very fast intended double-click lands here tooFixClick slowly, or compare at a 60 ms threshold
A button does nothingCauseDead switch or remapped buttonFixCheck the mouse software, then another USB port
A drag drops halfwayCauseThe contacts open for a moment while heldFixHold and drag test →

How to fix a double-click

Fixes: 5
FixHowEffectEffort
Contact the brandTry this first under warranty, and send the report as proofTry this first under warranty, and send the report as proofFixes it
Clean the buttonBlow compressed air into the gapBlow compressed air into the gapSometimes
Raise the debounce timeSet 8–10 ms; adds a little delaySet 8–10 ms; adds a little delayReduces it
Switch to an optical mouseNo contacts, no bounceNo contacts, no bounceFixes it
Replace the switchSolder in an Omron or Kailh of the same sizeSolder in an Omron or Kailh of the same sizeFixes it
After a fix, go back to the test area, click left and right 20 times each, and check that possible faults stay at 0.

Frequently asked questions

10 questions

What is a normal double-click speed?

100–250 ms

Most people double-click with 100 to 250 ms between the presses, and Windows accepts up to 500 ms by default. To measure how fast you can click instead, use the CPS test.

Why does my mouse double-click when I click once?

Switch bounce

When the contacts wear or oxidize, they bounce for longer than the debounce time, and one press is read as two.

What threshold should I use?

80 ms

If you click very fast, try 60 ms. A gap under 40 ms is almost always a fault.

Does one possible fault mean my mouse is broken?

Not always

Test the same button 2 or 3 more times in this mouse double click test. Only a fault that comes back each time points to the switch.

Can software fix a double-click?

It can hide it

A longer debounce time filters the bounce, but it adds delay to every click.

Why does only my left mouse button double-click?

Worn left switch

The left button is used most, so its switch wears first. Out of warranty, replacing just the left switch is enough.

My new mouse double-clicks. Is that normal?

No

A new mouse should show no possible faults. Return or exchange it within the return period.

Do optical switches double-click?

Rarely

Optical switches read a light beam instead of metal contacts, so contact bounce cannot cause a double-click.

How is this different from the hold and drag test?

Different moment

The double-click test looks for an extra press at the moment you press. The hold and drag test looks for a break while you hold the button.

Why is there no right-click menu in the test area?

Turned off

The test area blocks the right-click menu, the back button and middle-click scrolling. They work again outside it.