MouseTester.io
Counts—
Over 10 cm—
Angle—
01Mouse at 0 on a ruler02Click the test area03Move 10 cm, then click again

Result

Not started
—DPI
Horizontal, shown after one run
Deviation from rated—
Conditions—
RawStraightDistance3 runs
Vertical ÷ horizontal—
Horizontal—
Vertical—
Place a ruler on the desk, then click the test area above to start

Every run

How to test

About 1 minute
01
Place a rulerStart at 0
02
Click to startPointer locks
03
Move 10 cmStraight along the ruler, then click
04
Average 3 runsIn both directions

TipPress the DPI button on your mouse to switch settings, measure each one, then compare them under Every run.

How to change mouse DPI and sensitivity

3 places

DPI, pointer speed and game sensitivity multiply together. Fine-tune with the last two.

01DPI buttonOn the mouse or in the driver

Each press moves to the next setting, and most mice show it with a light. Measure each setting here to see its real DPI.

02System pointer speedWindows: Settings › Bluetooth & devices › Mouse
Mac: System Settings › Mouse › Tracking speed

For games, keep the default and turn off Enhance pointer precision; raw input ignores it.

03In-game sensitivityGame settings

DPI × sensitivity is eDPI, and the same eDPI feels the same. If you double the DPI, halve the sensitivity.

Same feel in another gameCS2, Valorant, Apex and 8 moreConvert

DPI meaning: how the counts add up

It takes four steps to get from your hand to the cursor; DPI is the second.

Hand moves1inchOne inch on the desk, 2.54 cm
Read hereSensor reports1600countsCounts per inch is the DPI
System×1default speedMultiplied by pointer speed, plus any acceleration
Cursor moves1600pixelsScreen pixels
Not changed by system settingsIn Chrome and Edge, this page reads the raw counts at step two, before pointer speed and Enhance pointer precision apply.

Where errors come from

4 causes

Check which way the result is off to find the cause. Within ±5% is normal.

Cause
1 mm measuring errorLonger is more accurate
Moving at an angleAngled moves read high
Lifting the mouseKeep it on the pad
Wrong surfaceGlossy desks lose counts
LowCheck for lifting, change the mouse pad
HighMove straight along the ruler
VariesMeasure the distance, average 3 runs

Frequently asked questions

11 questions

What is DPI on a mouse, and what does DPI mean?

Counts per inch

DPI means dots per inch, also called CPI (counts per inch). It is how many counts the mouse sensor reports for one inch of movement. The higher the DPI, the further the cursor moves for the same hand movement.

How do I check my mouse DPI?

Measure it here

The driver software usually shows the current setting, and some mice show it with a light. To find the real value, use this mouse DPI tester: move the mouse a measured distance along a ruler, and the page divides the counts by the distance. No installation is needed.

How do I change my mouse DPI?

DPI button or driver

Most mice have a DPI button that steps through a few settings, and the driver software sets the exact values. Test each setting here to see its real DPI. For fine changes, use the system pointer speed or the in-game sensitivity.

What does the DPI button on a mouse do?

Changes the setting

Each press moves to the next DPI setting, often shown by a light on the mouse. The driver software sets which values the button steps through.

What is the difference between DPI and sensitivity?

Hardware and software

DPI is a hardware setting: how many counts the mouse reports per inch. Sensitivity is a software multiplier on those counts. Change the DPI first and keep the Windows pointer speed at its default (10 of 20 in Settings, the 6th notch in Control Panel) to keep the raw counts.

How far from the rated DPI is normal?

Within ±5%

Sensors and lenses have tolerances, so a DPI test result within ±5% of the rated value is normal. Past 10%, check the driver settings and measure again.

Why move 10 cm?

Longer is more accurate

A 1 mm error in the distance is 10% over 1 cm, but only 1% over 10 cm. Moving 4 inches gives about the same accuracy.

Does the pointer speed change the result?

Not in Chrome and Edge

In Chrome and Edge this page reads the raw movement of the mouse, which pointer speed and Enhance pointer precision do not change. In other browsers, turn off mouse acceleration first.

Can the horizontal and vertical DPI differ?

On a few mice

Some sensors, or drivers with separate X and Y DPI, give different values. Switch to Vertical and measure once to compare.

Is a higher DPI better?

Not always

DPI only sets how far the cursor moves for the same hand movement. Many FPS players use 400 to 1600 DPI and match it with their in-game sensitivity. A 4K screen has more pixels to cross, so it may need a higher DPI or pointer speed.

Can this DPI analyzer calibrate my mouse?

It measures, then you adjust

No. This online DPI analyzer only measures; it changes no settings. For mouse calibration, compare the measured DPI with the rated value and correct it in the driver. It also works as a mouse sensitivity test, since DPI is the hardware half of sensitivity.